K1-10
Dual-indicator -10 architecture combining a Standard Carrier and Side Carrier.
- Two indicator positions
- Standard + Side Carrier
- 1/8–1 in / 3–25 mm class
Universal Concentricity Gaging System
Dual Indicator
K1 Series · -10
K1-10 Dual Indicator Concentricity Gage
Standard Carrier + Side Carrier measurement architecture.
The Universal Punch K1-10 is a dual-indicator concentricity gage for cylindrical parts from 1/8–1 in (3–25 mm) in diameter and published part lengths up to 4 in (102 mm). The K1 architecture combines a Standard Carrier with a Side Carrier so two indicator positions can be configured around the same supported rotating part.
K1-10 dual-indicator architecture
Configured example shown with two indicator positions.
1/8–1 in
3–25 mm published part diameter class
Up to 4 in
102 mm published part length
Dual Indicator
Two configurable measurement positions
11.5 lb
5.2 kg published shipping weight
What Is the K1-10?
A dual-indicator -10 gage built around two measurement positions.
The K1-10 is the small-diameter member of Universal Punch's K1 dual-indicator concentricity-gage family. Universal Punch documentation defines the model as a Dual Indicator Gage / 3–25 mm / Standard Carrier / Side Carrier.
Its value is not simply that it holds two indicators. The K1-10 gives the inspection setup two separate carrier positions around one supported rotating part. The actual characteristics inspected at those positions depend on the component, contact points, roller geometry, indicator access and drawing requirement.
The Universal Punch K1-10 is a dual-indicator concentricity gage for 1/8–1 in (3–25 mm) diameter parts. It combines a Standard Carrier and Side Carrier, supports published part lengths up to 4 in (102 mm), and is designed for precision rotational inspection where two indicator positions are useful in one gaging setup.
Why Dual Indicator?
Two measurement positions can reveal more from one setup.
A single-indicator concentricity gage can be appropriate when one measurement location answers the inspection requirement. The K1-10 is designed for applications where the setup benefits from a second indicator position.
Because K1 combines the Standard Carrier and Side Carrier architectures, both indicator positions can be configured around the same supported component while the part is rotated through the gaging system.
Carrier 1
Standard Carrier
Primary indicator position within the K1 dual-indicator architecture.
Carrier 2
Side Carrier
Secondary measurement access from the side of the part.
Inspection-method note:
two indicators do not automatically define what is being measured. Indicator contacts and interpretation
should follow the actual drawing, datum scheme and inspection plan.
Published K1-10 Data
Technical specifications at a glance.
Universal Punch general-data literature groups the K1/K2 -10 platform at the dimensions below, while the K1 catalog listing independently confirms the K1-10 part envelope and shipping weight.
Part Diameter
1/8–1 in
3–25 mm
Part Length
Up to 4 in
102 mm
Shipping Weight
11.5 lb
5.2 kg
Published Gage Length
10.5 in
267 mm
Published Gage Width
6.5 in
165 mm
Published Gage Height
Approx. 6 in
152 mm
How the K1-10 Works
Support the part. Rotate the part. Observe two indicator positions.
01
Support the component on the selected roller geometry.
The roller set must match the usable cylindrical support surfaces and required clearance around the part.
02
Set the top-arm yoke and indicator contacts.
The adjustable top-arm assembly and carrier adjustments allow the contacts to be positioned around the application.
03
Rotate the part through the gaging position.
Universal Punch documentation identifies a manual timing-belt pulley system as the standard rotational drive architecture.
04
Observe both indicator positions.
The two carrier locations allow two measurement contacts to be configured around the same supported rotating component.
K1 vs. K2 vs. KK
Choose by measurement access—not diameter alone.
The K and KK families separate two- and three-indicator architectures by carrier arrangement.
K2-10
Dual-indicator -10 architecture combining a Standard Carrier and Vertical Carrier.
- Two indicator positions
- Standard + Vertical Carrier
- Choose when vertical access better matches the second measurement position
KK1-10 / KK2-10
Triple-indicator configurations for applications requiring three measurement positions.
- KK1: Standard + Two Side Carriers
- KK2: Standard + Side + Vertical Carrier
- Evaluate when two contacts are not enough
Configure the Complete System
The gage model is only the first decision.
Universal Punch defines the Concentricity Gaging System around three primary selections. The usefulness of the K1-10 depends on matching all three to the part.
01
Select the gage model
Choose K1-10 when the -10 size class and Standard + Side Carrier dual-indicator architecture fit the inspection.
02
Select the main rollers
Match the support geometry to available cylindrical lands, shoulders, threads, grooves and required feature clearance.
03
Select indicators & accessories
Confirm indicator resolution, range, stylus access, mounts, stops, calibration requirements and optional drive system.
K1-10 Roller Options
Match roller contact to the component geometry.
Because the K1-10 is a -10 model, it uses the published -10 main roller families. The correct choice depends on the available support surfaces and the feature being inspected.
Full Plain
110-10FP
Half Plain
110-10HP
Quarter Plain
110-10QP
Full Plain Zero
110-10FZ
Half Plain Zero
110-10HZ
Quarter Plain Zero
110-10QZ
Thin Zero Plain
110-10TZ
Special Top Contacts
Multiple published -10 options
Selection guidance:
choose rollers from the actual part geometry. Available cylindrical lands, shoulder clearance,
thread location and the measurement feature can all change the appropriate support arrangement.
Accuracy, Indicators & Drive
Specify the complete measurement requirement.
Accuracy classification, indicator resolution and rotation method should be considered together when configuring a K1-10 system.
Published Accuracy Classes
Standard Black / Precision Gold
≤ 4 µm
Standard Black
≤ 2 µm
Precision Gold eligibility for applicable -10 / -20 models
Confirm the exact K1-10 accuracy classification, indicator resolution, calibration and documentation requirements when ordering.
Optional Powered Rotation
K1-10 Variable-Speed Motor Assembly
0–10 rpm
Published variable-speed system range
15 in
381 mm K1-10 motorized base plate listing
Universal Punch documentation identifies a 24 VDC variable-speed motorized system for selected gage models, including a dedicated K1-10 assembly. Confirm transformer, controller and final drive configuration with the quote.
Where K1-10 Fits
Best suited to small-part inspections that benefit from two indicator positions.
The K1-10 is worth evaluating when the part fits the -10 size class and the inspection arrangement benefits from a second measurement position accessed from the side.
- Part diameter fits 1/8–1 in / 3–25 mm.
- Published part length fits up to 4 in / 102 mm.
- Two indicator positions are useful in one rotational setup.
- Side-carrier access is appropriate for the second measurement position.
- The part has suitable support surfaces for the selected roller geometry.
K1 Series Size Comparison
K1-10, K1-20 and K1-40.
The same Standard + Side Carrier architecture is published across three common diameter classes.
| Model | Part Diameter | Part Length | Published Shipping Weight | Architecture |
|---|---|---|---|---|
| K1-10 | 1/8–1 in / 3–25 mm | Up to 4 in / 102 mm | 11.5 lb / 5.2 kg | Standard + Side Carrier |
| K1-20 | 3/8–2 in / 10–50 mm | Up to 6 in / 152 mm | 14.8 lb / 6.8 kg | Standard + Side Carrier |
| K1-40 | 3/4–4 in / 20–102 mm | Up to 8 in / 203 mm | 18.5 lb / 8.4 kg | Standard + Side Carrier |
K1-10 Technical FAQ
Questions buyers and inspectors ask before specifying the gage.
The Universal Punch K1-10 is a dual-indicator concentricity gage for cylindrical parts in the 1/8–1 in (3–25 mm) diameter class. It combines a Standard Carrier with a Side Carrier and supports published part lengths up to 4 in (102 mm).
The K1-10 provides two carrier positions so two indicator contacts can be configured around the same supported rotating part. The exact characteristics measured at those locations depend on the component, contact points and inspection requirement.
Both are dual-indicator -10 concentricity gages. The K1-10 combines a Standard Carrier and Side Carrier. The K2-10 combines a Standard Carrier and Vertical Carrier.
The published K1-10 diameter range is 1/8–1 in (3–25 mm), with part lengths up to 4 in (102 mm).
Universal Punch general-data literature lists the K1/K2-10 platform at approximately 10.5 in (267 mm) long, 6.5 in (165 mm) wide and approximately 6 in (152 mm) high.
The published K1-10 shipping weight is 11.5 lb (5.2 kg).
Published -10 main roller families include Full Plain, Half Plain, Quarter Plain, Full Plain Zero, Half Plain Zero, Quarter Plain Zero and Thin Zero Plain, along with multiple top-roller and specialized contact options.
Universal Punch parts documentation lists both standard dial test indicators and digital indicator options. Indicator resolution, range, stylus reach and mounting should be selected around the application.
Yes. Universal Punch lists a K1-10 variable-speed motor assembly with a 15 in (381 mm) base plate. The variable-speed drive documentation identifies a 24 VDC, 0–10 rpm system architecture.
Universal Punch documentation identifies Precision Gold classification for eligible -10 and -20 model classes at better than or equal to 2 µm. Confirm the exact K1-10 configuration, calibration and indicator requirements when ordering.
Consider K1-10 when the part fits the -10 size class and the inspection benefits from two indicator positions, particularly when the second measurement position is best served by a Side Carrier.
Send the part drawing, diameter, overall length, available support surfaces, measurement locations, tolerance or inspection objective, indicator preference and any calibration or motorized-drive requirements.
Configure the K1-10 Around the Part
Start with the drawing—not the catalog photograph.
Send Universal Punch the part drawing, diameter, overall length, usable support surfaces, two intended measurement locations, tolerance or inspection objective, preferred indicators, calibration requirement and manual or motorized-drive preference. Our team can review the complete K1-10 configuration before the system is quoted.